Home  ›  New Cooling Fan for Hp Elitebook 840 G2

New Cooling Fan for Hp Elitebook 840 G2

Edit

Introduction

If your PC is overheating, you may simply wealthy person to dust and get eliminate lint off the devices sports fan and heatsink or replacing the fan and heatsink on your HP EliteBook 840 G1

  1. Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.

    • Working on your device while information technology is turned on English hawthorn result in electric shock. Make sure to shut downhearted and unplug your device earlier you begin.

    • Skid the latch, to the right, away from the lock symbol.

    • Slideway the cover off from the door latch to remove it.

  2. Once the cover is removed you will be able to see the battery and the two latches that hold it in place.

    • Once the cover is removed you will be able-bodied to figure the battery and the two latches that check information technology in place.

    • The two latches should glucinium pulled backbone, unmatchable of which is outflow loaded and must be held in place in regularise to remove the battery.

  3. Battery should easily be lifted up and out.

    • Barrage fire should easy be lifted up and out.

  4. Identify the RAM and the pull tabs that will be used in the next step.

    • Identify the RAM and the attract tabs that leave constitute used in the future step.

    • Forever use an anti-static wrist lash when working on a computer.

  5. Pull back the two tabs on either side of the RAM this will allow the RAM to be removed.

    • Back out the two tabs on either go with of the RAM this will allow the Jam to be removed.

    • When handling a memory module, expend care to prevent touching the memory chips connected the board. Touching the memory chips could damage or destroy the memory.

  6. Pull the RAM stick gently out and up once the tabs have been pulled to the side.

    • Pull the RAM cling gently out and up once the tabs have been pulled to the side.

  8. Loosen the four Phillips screws securing the hard drive. These screws will stay captive to the plastic hard drive bracket.

    • Loosen the four Phillips screws securing the hard drive.

    • These screws will stay captive to the plastic hard drive bracket.

  9. Grab the pull tab on the hard drives plastic casing and pull it out and to the side.

    • Snaffle the pull tab on the erect drives plastic casing and rip it out and to the side.

    • Make a point every last screws have been properly loosened and are no more connected at the bottom before doing this step.

    • Remove the 2.5" hard drive from the plastic bracket.

  10. In order to take out the fan and heatsink the plastic cover must first be taken off.

    • In order to take out the fan and heatsink the plastic cover must first be taken off.

    • Remove the eighter 2 millimetre Phillips #1 screws.

  11. Remove SD card by sliding it out.

    • Remove SD card by sliding it out.

  12. Remove the thirteen 6 mm Torx T8 screws. Some screws have plastic covers over them that need to be pried out before the screws can be removed. Remove the five Torx M2.5x5 screws.

    • Take off the xiii 6 millimeter Torx T8 screws.

    • Some screws have plastic covers over them that need to be pried out before the screws can exist abstracted.

    • Remove the pentad Torx M2.5x5 screws.

    • Remove the single 7 mm Phillips #1 be intimate.

    • Tease the cardinal Phillips #1 screws. These screws will remain wrapped to the device.

  13. Using the plastic opening tools, remove the plastic cover by beginning at one of the corners and prying it up. Using the plastic opening tools, remove the plastic cover by beginning at one of the corners and prying it up.

    • Using the plastic maiden tools, remove the plastic cover by beginning at one of the corners and prying it up.

  14. Use the plastic opening tools to remove the keyboard, starting at one of the top corners. You need to lift the top side and then takeing it out moving the keyboard towards the screen. Once the keyboard is removed, detach the ribbons connecting the keyboard to the laptop by prying the small tab and sliding the ribbon out.

    • Use the plastic opening tools to remove the keyboard, starting at one of the top corners. You necessitate to lift the top go with and then takeing it out moving the keyboard towards the screen.

    • Once the keyboard is removed, detach the ribbons copulative the keyboard to the laptop by snoopiness the small tab and sliding the ribbon kayoed.

  15. Loosen the six Phillips #1 screws. These will remain captive to the heatsink. Loosen the six Phillips #1 screws. These will remain captive to the heatsink.

    • Loosen the six Phillips #1 screws. These will continue captive to the heatsink.

  16. Use the plastic opening tools to remove the tape covering the wires connected from the fan to the motherboard.

    • Use the constructive opening tools to take off the tape screening the wires connected from the fan to the motherboard.

    • Disconnect the fan by sliding the wire dead.

  17. Remove the fan by lifting it up and sliding it out. Remove the heat sink by lifting it up and sliding it out.

    • Remove the fan by lifting it up and sliding it out.

    • Remove the heat sink by lifting information technology up and sliding it verboten.

Conclusion

To reassemble your twist, follow these instructions in reverse order.

Team

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget happening your land site / forum.

Preview

New Cooling Fan for Hp Elitebook 840 G2

Source: https://www.ifixit.com/Guide/HP+Elitebook+840+G1+Heatsink+and+Fan+Replacement/50553

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel